Have ideas to improve npm?Join in the discussion! »

    tessel-thermalprinter

    0.3.0 • Public • Published

    Thermal printer module for Tessel

    Support for the A2 micro panel thermal printer module for Tessel.

    This module is based on xseignard's thermalprinter package

    Important Information Specific to Module

    • Needs a seperate 5v - 9V, 2A power supply. The Tessel can't power this. 9V is faster.
    • You can do a test print by holding the printer button while powering.

    Installation

    npm install tessel-thermalprinter
    • A, B, D ports only. C doesn't support UART yet.
    • Wire it up so: Ground (printer) to Ground (Tessel: Pin 0), RX (printer) to RX/G1 (Tessel: Pin 8) add pics later

    Examples

    var tessel = require('tessel');
    var thermalprinter = require('tessel-thermalprinter');
    var printer = thermalprinter.use(tessel.port['A']);
     
    printer.on('ready', function(){
     
        console.info('Printer ready!');
     
        printer
            .center()
            .horizontalLine(16)
            .printLine("we're printing with")
            .inverse(true)
            .big(true)
            .printLine(' TESSEL! ')
            .lineFeed(3)
            .print(function(){
                console.info('Printer finished!');
                process.exit();
            });
     
    });

    For the Last.fm example you'll need to add a api key. You can get one here on their website.

    Methods

    Settings

    # printer.setMaxPrintingDots( maxPrintingDotsValue, callback() )
    _Set the max printing dots (0-255). Default: 7 (( 7 + 1 ) * 8 = 64dots). Unit: ( n + 1 ) * 8dots

    According to section 5.2.9 of the datasheet: "The more max heating dots, the more peak current will cost when printing, the faster printing speed. The max heating dots is 8 * ( n + 1 ).""

    # printer.setHeatingTime( heatingTimeValue, callback() )
    Set the heating time (3-255). Default: 80 (800µs). Unit: 10µs.

    According to section 5.2.9 of the datasheet: "The more heating time, the more density, but the slower printing speed. If heating time is too short, blank page may occur."

    # printer.setHeatingInterval( heatingIntervalValue, callback() )
    Set the heating interval (0-255). Default: 2 (20µs). Unit: 10µs.

    According to section 5.2.9 of the datasheet: "The more heating interval, the more clear, but the slower printing speed."

    # printer.setLineSpacing( spacing )
    Set the space between each printed line vertically

    Main methods

    # printer.reset()
    Resets printer

    # printer.print( callback() )
    Runs commands and prints. Run this last.

    # printer.printLine( text )
    Write text to printer

    # printer.lineFeed( amountOfLines )
    Feed blank lines out of the printer specified by argument

    Printing modes

    # printer.bold( onOff )
    Makes text bolder

    # printer.big( onOff )
    Makes text bigger

    # printer.underline( onOff )
    Makes text underlined

    # printer.small( onOff )
    Makes text smaller

    # printer.upsideDown( onOff )
    Makes text upside down

    # printer.inverse( onOff )
    Makes text black on white

    # printer.left( onOff )
    Makes text aligned left

    # printer.right( onOff )
    Makes text aligned right

    # printer.center( onOff )
    Makes text aligned center

    Images

    soooooon

    Barcodes

    # printer.barcodeTextPosition( positionValue )
    Set text position relative to barcode. Positions are: 0: Not printed 1: Above the barcode 2: Below the barcode 3: Both above and below the barcode

    # printer.barcode( Printer.BARCODE_TYPES.type, barcodeData )
    Print barcode. The types you can use are: UPCA, UPCE, EAN13, EAN8, CODE39, I25, CODEBAR, CODE93, CODE128, CODE11, MSI

    Other

    # printer.indent( amountOfColumns )
    Create an indentation for text by an amount of cplumns

    # printer.horizontalLine( length )
    Draw a horizontal line at a certain length

    check the example, will add the rest later

    Events

    # printer.on( 'ready', callback() )
    Emitted upon reset and printing settings on printer.

    Further Examples

    If you want to set options you can do so like this:

    // ...
     
    var printer = thermalprinter.use(tessel.port['A'], {
     
        // baudrate for the printer default: 19200
        baudrate: 19200,
        /* can be found by doing a print test. hold the button printer while
         * powering the printer on and it should spit out some shit at the
         * bottom is it should say the baudrate
         */
     
        // Max printing dots (0-255), unit: (n+1)*8 dots, default: 7 ((7+1)*8 = 64 dots)
        maxPrintingDots: 7,
        /* The more max heating dots, the more peak current will cost when printing,
         * the faster printing speed. The max heating dots is 8*(n+1).
         */
     
        // Heating time (3-255), unit: 10µs, default: 80 (800µs)
        heatingTime: 80,
        /* The more heating time, the more density, but the slower printing speed.
         * If heating time is too short, blank page may occur.
         */
     
        // Heating interval (0-255), unit: 10µs, default: 2 (20µs)
        heatingInterval: 2,
        /* The more heating interval, the more clear, but the slower printing speed.
         */
    });
     
    // ...

    Hardware specifications and Advanced Information

    • Datasheet

    • Productsheet

    • Buy in US (Adafruit) / UK (Hobbytronics)

    • Requires 5-9VDC @ 1.5Amp power supply during print

    • Protocol: TTL Serial, 19200 baud

    • Mean Cycles Before Failure: 5 million lines

    • Printing Speed: 50-80mm/s

    • Resolution: 8 dots/mm, 384 dots/line

    Dimensions

    • Requires 2.25" wide, 50 ft or shorter thermal paper
    • Effective Printing Width: 48mm
    • Outline Dimension (WxDxH): 111x65x57mm
    • Installation Port Size: 103 x 57mm

    Character set

    • Character Set: ASCII,GB2312-80(Chinese)
    • Print Font: ANK:5×7, Chinese: 12x24,24×24

    Paper

    • Paper Type: Thermal paper
    • Paper Width: 57.5 ±0.5mm
    • Paper Roll Diameter: max 39mm

    Temperatures

    • Operating Temp: 5°C ~ 50°C
    • Operating Humidity: 10% ~ 80%
    • Storage Temp: -20°C ~ 60°C
    • Storage Humidity: 10% ~ 90%

    Other libraries

    Don't have a Tessel? As this uses serial it works with most things:

    Licensing

    MIT or Apache 2.0

    Install

    npm i tessel-thermalprinter

    DownloadsWeekly Downloads

    6

    Version

    0.3.0

    License

    MIT/Apache 2.0

    Last publish

    Collaborators

    • avatar