Naboo's Podracing Misadventure

    iobroker.rpi2

    1.3.1 • Public • Published

    Logo ioBroker RPI-Monitor Adapter

    Number of Installations Number of Installations NPM version

    Translation status Downloads

    RPI-Monitor implementation for integration into ioBroker. It is the same implementation as for iobroker.rpi, but with GPIOs.

    Important Information

    Works only with node >= 0.12

    ioBroker needs special permissions to control GPIOs. On most Linux distributions this can be achieved by adding the ioBroker user to the gpio group (recommended) or running ioBroker under root (less secure).

    Installation

    After installation you have to configure all required modules via administration page.

    After start of iobroker.rpi, all selected modules generates an object tree in ioBroker within rpi.. e.g. rpi.0.cpu

    Be sure, that python and build-essential are installed:

    sudo apt-get update
    sudo apt-get install -y build-essential python
    

    Following Objects are available after selection:

    CPU

    • cpu_frequency
    • load1
    • load5
    • load15

    Raspberry (vcgencmd is required)

    • cpu_voltage
    • mem_arm
    • mem_gpu

    Memory

    • memory_available
    • memory_free
    • memory_total

    Network (eth0)

    • net_received
    • net_send

    SDCard

    • sdcard_boot_total
    • sdcard_boot_used
    • sdcard_root_total
    • sdcard_root_used

    Swap

    • swap_total
    • swap_used

    Temperature

    • soc_temp

    Uptime

    • uptime

    WLAN

    • wifi_received
    • wifi_send

    Configuration

    On configuration page you can select following modules:

    • CPU
    • Raspberry
    • Memory
    • Network
    • SDCard
    • Swap
    • Temperature
    • Uptime
    • WLAN

    Logfiles / Configuration Settings

    Features

    Todo

    Tested Hardware

    • Odroid C1
    • Raspberry Pi 1

    GPIOs

    You can read and control GPIOs too. All what you need to do is to configure in the settings the GPIOs options (additional tab).

    GPIOs

    After some ports are enabled following states appear in the object tree:

    • rpi.0.gpio.PORT.state

    The numeration of ports is BCM (BroadComm pins on chip). You can get the enumeration with gpio readall. For instance PI2:

    +-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+
    | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
    +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
    |     |     |    3.3v |      |   |  1 || 2  |   |      | 5v      |     |     |
    |   2 |   8 |   SDA.1 | ALT0 | 1 |  3 || 4  |   |      | 5V      |     |     |
    |   3 |   9 |   SCL.1 | ALT0 | 1 |  5 || 6  |   |      | 0v      |     |     |
    |   4 |   7 | GPIO. 7 |   IN | 1 |  7 || 8  | 0 | IN   | TxD     | 15  | 14  |
    |     |     |      0v |      |   |  9 || 10 | 1 | IN   | RxD     | 16  | 15  |
    |  17 |   0 | GPIO. 0 |   IN | 0 | 11 || 12 | 0 | IN   | GPIO. 1 | 1   | 18  |
    |  27 |   2 | GPIO. 2 |   IN | 0 | 13 || 14 |   |      | 0v      |     |     |
    |  22 |   3 | GPIO. 3 |   IN | 0 | 15 || 16 | 0 | IN   | GPIO. 4 | 4   | 23  |
    |     |     |    3.3v |      |   | 17 || 18 | 0 | IN   | GPIO. 5 | 5   | 24  |
    |  10 |  12 |    MOSI |   IN | 0 | 19 || 20 |   |      | 0v      |     |     |
    |   9 |  13 |    MISO |   IN | 0 | 21 || 22 | 1 | IN   | GPIO. 6 | 6   | 25  |
    |  11 |  14 |    SCLK |   IN | 0 | 23 || 24 | 1 | IN   | CE0     | 10  | 8   |
    |     |     |      0v |      |   | 25 || 26 | 1 | IN   | CE1     | 11  | 7   |
    |   0 |  30 |   SDA.0 |   IN | 1 | 27 || 28 | 1 | IN   | SCL.0   | 31  | 1   |
    |   5 |  21 | GPIO.21 |   IN | 1 | 29 || 30 |   |      | 0v      |     |     |
    |   6 |  22 | GPIO.22 |   IN | 1 | 31 || 32 | 0 | IN   | GPIO.26 | 26  | 12  |
    |  13 |  23 | GPIO.23 |   IN | 0 | 33 || 34 |   |      | 0v      |     |     |
    |  19 |  24 | GPIO.24 |   IN | 0 | 35 || 36 | 0 | IN   | GPIO.27 | 27  | 16  |
    |  26 |  25 | GPIO.25 |  OUT | 1 | 37 || 38 | 0 | IN   | GPIO.28 | 28  | 20  |
    |     |     |      0v |      |   | 39 || 40 | 0 | IN   | GPIO.29 | 29  | 21  |
    +-----+-----+---------+------+---+----++----+---+------+---------+-----+-----+
    | BCM | wPi |   Name  | Mode | V | Physical | V | Mode | Name    | wPi | BCM |
    +-----+-----+---------+------+---+---Pi 2---+---+------+---------+-----+-----+
    

    DHTxx/AM23xx Sensors

    You can read from DHT11, DHT22 and AM2302 temperature/humidity sensors.

    Connect such a sensor to a GPIO pin as described on the node-dht-sensor package page. Multiple sensors can be connected to multiple pins (this is not a bus system) as discussed.

    Changelog

    1.3.1 (2021-07-16)

    • (Apollon77) Prevent js-controller 3.3 warnings

    1.3.0 (2021-07-16)

    • (asgothian) Fix to get CPU frequencies also on Raspi 4
    • (raintor) Add support for DHTxx/AM23xx Sensors
    • (raintor) Configure internal Pull UP/Down Resistor
    • (raintor) Add port 'label'/'friendly name' to GPIO config

    1.2.0 (2020-01-17)

    • (janfromberlin) GPIO configuration as output with defined initial value
    • (foxriver76) No longer use adapter.objects
    • (Apollon77) Adjust gpio errors

    1.1.1

    • (Apollon77) Error messages for not existing values are logged only once

    1.1.0

    • (Apollon77) Nodejs 10 support

    1.0.0 (2018-08-20)

    • (bluefox) Admin3 support

    0.3.2 (2017-11-29)

    • (Homoran) fixed Mem available readings on Stretch

    0.3.1 (2017-01-11)

    • (olifre) Fixup swap_used calculation.

    0.2.2 (2016-12-01)

    • (bluefox) Add GPIO direction indication

    0.2.2 (2016-11-22)

    • (bluefox) Use BCM enumeration

    0.2.1 (2016-10-29)

    • (bluefox) fix start of adapter

    0.2.0 (2016-10-23)

    • (bluefox) just version change

    0.1.1 (2016-10-13)

    • (bluefox) implement GPIOs control

    0.0.4 (2016-03-25)

    • (bluefox) Try catch by eval (bluefox) do not process if exec fails

    0.0.3 (2015-12-28)

    • (husky-koglhof) Fixed value calc. Set Value to 2 digits

    0.0.2 (2015-12-26)

    • (husky-koglhof) Workaround for node 0.10.x
    • (bluefox) Some Fixes

    0.0.1 (2015-12-23)

    • Initial commit. Alpha Version.

    License

    Copyright (c) 2015-2021 husky-koglhof husky.koglhof@icloud.com

    MIT License

    Install

    npm i iobroker.rpi2

    DownloadsWeekly Downloads

    621

    Version

    1.3.1

    License

    MIT

    Unpacked Size

    345 kB

    Total Files

    16

    Last publish

    Collaborators

    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar
    • avatar